Netvio NET-IP-SW24P-10, 24-Port 1GB 1U Plug & Play AVoIP Network Switch With Zero Configuration

The Netvio IP-SW-24P-10 is a dedicated plug ‘n’ play AVoIP Switch designed for use with Netvio and other AV over IP solutions. It comes preconfigured for multicast AVoIP solutions, requiring zero configuration for systems with up to 21 encoders and/or decoders.

Description
The Netvio IP-SW-24P-10 is a dedicated plug ‘n’ play AVoIP Switch designed for use with Netvio and other AV over IP solutions. It comes preconfigured for multicast AVoIP solutions, requiring zero configuration for systems with up to 21 encoders and/or decoders.

All ports support POE with a total 450W PoE budget, which is large enough to power devices connected to all ports simultaneously.

There is an additional Gigabit copper and dual SFP fibre module ports for local area connection, enabling the distribution of JP4 series preview streams without complicated VLAN configuration.

The Netvio IP-SW-24P-10 is designed and suitable for systems with 21 or less AVoIP end points only. Multiple IP-SW-24P-10 switches cannot be used in the same system unless they are completely isolated systems. It is only designed to connect to AVoIP encoders and decoders.

Please Note: Due to its configuration, it is not recommended that other AV or IT equipment is connected to this switch.

This switch’s power input supports input voltages of 100 to 240VAC, 50/60Hz.

The power LED lights up when the switch is connected to a power source and the rear switch is powered on. The link indicator light indicates the network connection through the corresponding port. Flicker indicates that the switch is sending or receiving data PoE indicator: The ‘On’ indicates that a device is connected to the corresponding port and drawing power and the ‘Off’ indicates that the port is not powered or no device is found.

For grounding, please use specialised ground lead connected to the ground.

Zero configuration
Plug ‘n’ play for Netvio IP video and control solutions
24 Gigabit ports with PoE
Connectivity for Netvio IP-JP4-CL-10 and up to 21 TX, RX end points
Large 450W PoE budget to power every connected device
Additional Gigabit copper and SFP fibre module ports for local area connection

Specs:

Network Interfaces - 24 x 10/100/1000Mbps RJ45 Ethernet ports
2 x 1Gbps SFP Ports
LED Indicators - Power, Link, PoE

Performance
Switching Capacity - 52Gbps
Jumbo Frame Size - 16KByte
Forwarding Capacity - 38.7Mpps
ACL Table - 512
Forwarding Mode Store and forward - VLANs 2, Packet Buffer Memory 4.1Mbit
RAM for CPU - 1Gbit
Flash Memory - 128Mbit
MAC Address Table - 8K
Power Method - 100 to 240VAC, 50/60HZ
Power Consumption - 30W

Power Over Ethernet
PoE Ports - 24
PoE Standard - IEEE802.3af, IEEE802.3at
PoE Power Budget - 430W
Max. PoE Wattage Per Port - 30W
PoE Voltage - 52V
PoE Pin Assignment - V- (RJ45 pin 1,2), V+ (RJ45 pin 3,6)
Casing - Metal

Temperature
Operating: 0°C / 32°F to 40°C / 104°F
Storage: -10°C / 14°F to 75°C / 167°F
Operating Humidity: 5% to 95% non condensing

Dimensions
Height: 44mm / 1.73″
Width: 440mm / 17.32″
Depth: 200mm / 7.87″

Installation
Rack mount or desktop

Included
Netvio IP-SW-24P-10
UK and EU mains cables
Rack mount and screws
Four switch rubber feet