Netvio NET-IP-SW48P-10, 48-Port 1GB 1U Plug & Play AVoIP Network Switch With Zero Configuration

The Netvio IP-SW-48P-10 is a dedicated plug 'n' play AVoIP Switch designed for use with Netvio and other AV over IP solutions. It comes preconfigured for multicast AVoIP solutions, requiring zero configuration for systems with up to 45 encoders and/or decoders.

The Netvio IP-SW-48P-10 is a dedicated plug 'n' play AVoIP Switch designed for use with Netvio and other AV over IP solutions. It comes preconfigured for multicast AVoIP solutions, requiring zero configuration for systems with up to 45 encoders and/or decoders.

All ports support POE with a total 850W PoE budget, which is large enough to power devices connected to all ports simultaneously.

There is an additional Gigabit copper and dual SFP fibre module ports for local area connection, enabling the distribution of JP4 series preview streams without complicated VLAN configuration.

The Netvio IP-SW-48P-10 is designed and suitable for systems with 45 or less AVoIP end points only. Multiple IP-SW-48P-10 switches cannot be used in the same system unless they are completely isolated systems. It is only designed to connect to AVoIP encoders and decoders.

This switch's power input supports input voltages of 100 to 240VAC, 50/60Hz.

The power LED lights up when the switch is connected to a power source and the rear switch is powered on. The link indicator light indicates the network connection through the corresponding port. Flicker indicates that the switch is sending or receiving data PoE indicator: The 'On' indicates that a device is connected to the corresponding port and drawing power and the 'Off' indicates that the port is not powered or no device is found.

For grounding, please use specialised ground lead connected to the ground.

Please Note: Due to its configuration, it is not recommended that other AV or IT equipment is connected to this switch.

Features:

- Zero configuration
- Plug 'n' play for Netvio IP video and control solutions
- 48 Gigabit ports with PoE
- Connectivity for Netvio IP-JP4-CL-10 and up to 21 TX, RX end points
- Large 850W PoE budget to power every connected device
- Additional Gigabit copper and SFP fibre module ports for local area connection

Specs:

Compatible With - Netvio and other AV over IP solutions
Systems with 45 or less AVoIP end points only
Network Interfaces - 48 x 10/100/1000Mbps RJ45 Ethernet ports
2 x 1Gbps SFP Ports
LED Indicators - Power, Link, PoE

Performance
Switching Capacity - 100 Gbps
Jumbo Frame Size - 12KByte
Forwarding Capacity - 74.4 Mpps
ACL Table - 4K
Forwarding Mode - Store and forward
VLANs - 2, Packet Buffer Memory 16 Mbit
RAM for CPU- 2 Gbit
Flash Memory - 256 Mbit
MAC Address Table - 32K
Power Method - 100 to 240VAC, 50/60HZ
Power Consumption - 30W

Power Over Ethernet
PoE Ports - 48
PoE Standard - IEEE802.3af, IEEE802.3at
PoE Power Budget - 850W
Max. PoE Wattage Per Port - 30W
PoE Voltage - 52V
PoE Pin Assignment - V- (RJ45 pin 1,2), V+ (RJ45 pin 3,6)
Casing - Metal
Temperature - Operating: 0°C / 32°F to 40°C / 104°F. Storage:
-10°C / 14°F to 75°C / 167°F
Operating Humidity: 5% to 95% non condensing

Dimensions
Height: 44mm / 1.73"
Width: 440mm / 17.32"
Depth: 350mm / 13.77"
Installation - Rack mount or desktop
Included - UK and EU mains cables
Rack mount and screws
Four switch rubber feet